FMX250 Mini H LED Night Flyer Quad Build

If you wish a nice flying in the night, build a FMX250 can be one of your best choices. FMX250 Mini H Quad frame kit comes with bulit-in LEDs that make the setup glow in the night sky and even more visible in the day.

If you are not sure about what spare parts you need, you can simply refer to the items that included in our FMX250 ARF/RTF packages.

Recommended Parts:

Frame: FMX250 250MM mini quadcopter with PCB board and LEDs x 1
Motor: DragonFly MC1806 KV2300 motor x 4
ESC: Dragonfly 12a ESC built-in 5V/2A BEC x 4
Propellers: 5030 electric CW/CCW props x 4 pairs
Flight Controller (Optional): Naze32 Acro Funfly flight controller (The same to ARF 1) / Naze 32 Full version flight Controller (The same to ARF 2)/ CC3D Flight Controller x1
Camera: SONY Effio-e 4140+811 1/3 CCD 2.6mm Lens 700TVL camera x 1
A/V Transimitter: Hawkeye 5.8g mini 600mw 32CH A/V transmitter x 1
Battery velcro straps x 2
5.8G clover 3-leaf TX antenna x 1
20CM servo extension cable  x 2
3M double sided adhesive tape x1
3S 1300-2200mAh Battery x1 (Not included in our ARF/RTF Package)

and silicon wires, straps, shrink tubes, T-plug etc that everything showed in the picture.

FMX250 Mini H Quad Build

Firstly, install the 4 motors. Here, we are using Dragonfly MC1806 2300kv Mini Motors.

Secondly, solder the ESC on PCB board. Please pay attention to the place of anode and cathode. And then solder the LED light and power supply board.

Thirdly, assemble the arms to PCB board. Please note that the ESC wires need to get through the fillister.

Fix the screws and assemble the bottom plate.

Install the long standoffs (spacers) and cushioning balls.

Solder the power supply connector. Please note that the red wire needs to be soldered to “+”, the black wire needs to be soldered to “-”.

Install the Flight Controller

Solder the the wires of the motors and ESC’s together, finished with head-shrink tubes.

Cut the outer part of camera.

Assemble to camera lens board with screws and nylon nuts.

Cut the wires of camera.

Cut the wire of A/V transmitter

Solder the black wire and yellow wire of camera together with exposed GND wire and yellow wire of A/V transmitter.

And then solder the power supply wire of A/V transmitter and red wire of camera together.

the red wire and black power supply wire left.

Solder them on the upper part of PCB 12V and GND

Assemble the A/V transmitter and fixed by a bolt.

Fix the cushioning balls by using nylon screw nuts, and then use the screw glues onto the screws.

Finally, connect the camera to the connector of A/V transmitter, and then assemble the upper part of FMX250 frame.

The build of FMX250 Mini H Quad is done!!!


ZMR250 250mm Mini Quadcopter FPV ARF Package Sold at US$199.99

Only US$199.99 for a whole FPV ARF package!!!

Three options of flight controller: Naze 32 Acro, Naze 32 Full, or the CC3D.

The FPV ARF Package is now available at

An affordable Mini ARF package that comes complete with heat shrink, cable sheathing, FC w/ PID settings and full FPV gear for the quad frame. What do you think? Refer to my previous post 

This FPV ARF package comes with ZMR250 carbon fiber frame. 250mm. Carbon Fiber has a nice sheen to the finish and all tooling edges are nice and smooth. Using Dragonfly MC1806 2300kv Mini Motors.
All up weight 498g.
This is a ZMR250 FPV ARF combo, It includes almost everything you need for your building work with ZMR250. Don’t worry what you need and just enjoy the  building process, we provide you with a promotion price and make sure you will get a perfect flying experience with our ARF package.
Package Includes:
Battery velcro straps x 2
5.8G clover 3-leaf TX antenna x 1
3M double sided adhesive tape x1
Also, silicon wires, straps, shrink tubes, T-plug etc that everything as showed in above pictures.
What else you need (choice which you prefer from our website):
Radio, battery (3s 1300-2200mah), receiver and monitor.

ZMR250 250mm Carbon Fiber Mini FPV Quadcopter Frame Kit on Hot Sale


zmr250-package-3 zmr250-package-2 zmr250-package-4

ZMR250 is a light weight, small size mini quadcopter with long flight time and easy to refit. The frame body with 1.5mm carbon fiber plate and the frame-arm also adopts 3mm carbon fiber plate, it ensures the strength and reduces the vibration when flying.Adopting the aluminum alloy column for connecting, make the plane more firm.

Now, ZMR250 is only sold at a price of US$33.60 ea. 


Arm plate thickness: 3mm

Main material: carbon fiber

Wheelbase: 250mm

Weight: 113g (without screws), 143g (with screws)

With rubber damper to decrease vibration during flight.

Aluminum alloy spacer, light weight, reliable.

Recommended parts (package not include):

Propeller: 5-6 inch

Motor: 1806-2208 series 1800-2200KV

ESC: 8A-12A

Battery: 1300Mah-2200Mah check here

Package included:

1 x ZMR250 Mini Quadcopter Multicopter Frame Kit

4 x damping ball